FIF Blog
FIF Blog
mobile logo How Do You Cut Legs off Bar Stool?

Bar Stools Tag

How Do You Cut Legs off Bar Stool?
August 11, 2026

How Do You Cut Legs off Bar Stool?

Shortening bar stool legs is a straightforward job when the marking and cutting are done in the right order. This guide sets out the full process: measuring each leg separately, scribing a line parallel to the floor on splayed frames, using masking tape and a mitre box for a square cut, then levelling and sealing the ends afterwards. We explain how to handle timber and metal tube differently, what to do when a footrest ends up too close to the floor, and which frames should never be cut at all. There is practical advice on floor protectors, touch up finishes and when replacing the stools makes more sense than modifying them. We also cover working safely with clamps and glasses, how to approach sled bases, cross braced frames and adjustable feet, and why every fixing should be rechecked a week after the job is finished, once the frame has settled into its new proportions under daily use....

Continue Reading
How Do You Measure Height of Bar Stools?
August 11, 2026

How Do You Measure Height of Bar Stools?

Measuring a bar stool sounds obvious until the tape is in your hand and the legs splay outwards. This guide explains the correct method: stand the stool on a hard level floor and measure vertically from the floor to the highest point of the seat, ignoring the backrest and footrest. We cover why padded seats should be measured uncompressed, how much sink to allow once someone sits down, and how to handle contoured seats and swivel mechanisms. Beyond seat height, we set out the other figures that decide whether a stool works in your kitchen: overall height, seat depth, seat width, footrest position and base diameter. There is a method for testing an ideal height using a dining chair and cushions before anything is ordered, an explanation of why two stools with identical stated heights can feel different, and a short list worth saving for future reference....

Continue Reading
What Height Bar Stools for 42 Inch Counter?
August 11, 2026

What Height Bar Stools for 42 Inch Counter?

A 42 inch counter is about 107cm, which puts it firmly in the bar height category rather than the standard worktop category. This guide gives the seat height you need, roughly 30 to 32 inches or 76cm to 81cm, and shows the calculation in both imperial and metric so you can check it against any surface. It explains why counter height stools leave an uncomfortable 16 inch gap, how a thick stone or timber top quietly reduces your clearance, and why footrests and base width become far more important as seat height rises. There is also advice on knee room and overhang on narrow raised bars, choosing adjustable stools by their maximum height, spacing and walkway clearance, and what to do if you have already bought the wrong size....

Continue Reading
How Much Does It Cost to Reupholster Bar Stools UK?
August 11, 2026

How Much Does It Cost to Reupholster Bar Stools UK?

Reupholstering a bar stool in the UK usually costs between 40 and 90 pounds per stool in labour for a simple round seat pad, rising well beyond that for shaped seats with backs, arms, piping or buttoning, with fabric charged separately in most cases. This guide breaks down the four factors that drive any quote: seat construction, detailing, the condition of the foam and webbing beneath, and your choice of cloth. We give realistic cost bands for single stools and for a set of four, explain what a DIY recover costs in materials, and set out how to judge whether recovering or replacing is the sounder decision for your frames. There is practical advice on gathering an accurate quote, the three questions worth asking every upholsterer, fabric quantities per seat, and a short FAQ on the numbers people ask about most....

Continue Reading
How High Should a Counter Be for Bar Stools?
August 11, 2026

How High Should a Counter Be for Bar Stools?

The right counter height depends entirely on the stools you plan to use, and the reliable way to link the two is the clearance between seat and surface. This article gives the counter heights that suit counter height and bar height seating, explains why UK worktops usually land at 90cm to 92cm, and covers what to do when a surface falls between the standard bands. It looks at the overhang depth knees genuinely need, the frames, brackets and skirting that reduce real clearance, and how footrests and backrests become more important as the counter rises. There is practical guidance for small kitchens and a short measuring checklist to work through before ordering....

Continue Reading
How Tall Should Bar Height Stools Be?
August 11, 2026

How Tall Should Bar Height Stools Be?

Bar height stools should place the seat between 750mm and 800mm from the floor, which works with a surface of 1050mm to 1100mm. The rule behind it is a 250mm to 300mm gap between seat top and counter underside, and applying it correctly matters more than any product name. This guide explains how to measure the surface properly, including allowances for unfinished floors and thick worktops, and sets out the three standard height bands so you can identify which one your kitchen actually needs. It also covers why footrests become essential above 700mm, how household height differences point towards adjustable gas lift seats, safety considerations with children, and the seven point checklist worth running through before ordering....

Continue Reading
How Do You Shorten Bar Stool Legs?
August 11, 2026

How Do You Shorten Bar Stool Legs?

Shortening bar stool legs is a straightforward job that goes wrong for predictable reasons, most often because the legs were marked from an uneven floor rather than from the seat. This guide explains how to calculate exactly how much to remove, why foot ferrules and pads belong in that calculation, and how to transfer a consistent line around all four legs. It covers cutting technique for wooden legs with a fine tooth saw and a clamped guide, the different approach needed for hollow metal tube, and how to handle splayed legs that require an angled cut. It also sets out the cases where cutting is the wrong answer, including gas lift columns and turned profiles....

Continue Reading
How Do You Stop Bar Stools from Scratching Floor?
August 11, 2026

How Do You Stop Bar Stools from Scratching Floor?

Scratched floors around a kitchen island are rarely the fault of the stool itself. The real culprit is grit trapped between the foot and the floor, and understanding that changes how the problem is solved. This guide starts by identifying what actually touches your floor, from bare metal tube ends on gas lift bases to square cut timber legs, then matches the right protector to engineered timber, laminate, vinyl, tile, stone, polished concrete and carpet. It explains why pads fail, how to prepare and fit them so they stay put, and the maintenance routine that keeps them working. There is also advice on the design features that reduce floor wear naturally, including swivel seats, proper footrests and backless stools that tuck away, plus guidance on rugs and repairing existing surface marks....

Continue Reading
How Do You Measure for Kitchen Bar Stools?
August 11, 2026

How Do You Measure for Kitchen Bar Stools?

Measuring for kitchen bar stools comes down to three figures, and this guide explains how to take each one properly. The first is height, measured to the underside of the worktop rather than the top, with guidance on clearance, planned floor finishes and how padded seats compress in use. The second is the length of the seating run, with advice on excluding corners and appliance doors, allowing 60cm to 70cm per person and thinking in centres rather than widths. The third is the clear floor depth behind the stools, which decides whether anyone can walk past a seated person. There are also notes on the four stool measurements worth comparing, how swivel bases behave in tight rows, a simple floor marking and book stacking test, and the mistakes that most often lead to returns....

Continue Reading
Are the Arms Removable on the Bar Stool?
August 11, 2026

Are the Arms Removable on the Bar Stool?

Arms on bar stools are usually fixed rather than removable, because they are either formed as part of the upholstered shell or built into the frame itself. Only designs with separately bolted armrests can be taken apart, and this guide shows you how to check which type you own by looking for fixing plates and bolts beneath the seat. We explain the three common constructions, why arms often brace the backrest, and the risks of modifying an assembled stool. There is practical help for the problem that prompts the question most often, namely arms catching under a counter overhang, along with the clearance figures you need. We also weigh the comfort case for arms against the flexibility of armless designs, look at mixing both in one kitchen, and finish with a short FAQ....

Continue Reading