FIF Blog
FIF Blog
mobile logo How Do You Know What Height Bar Stool?

Bar Stools Tag

How Do You Know What Height Bar Stool?
August 12, 2026

How Do You Know What Height Bar Stool?

Knowing what height bar stool you need takes one measurement and one subtraction, yet buying by category name is where most people go wrong. This guide explains why the 25cm to 30cm gap between seat and counter underside exists, what happens at either extreme of it, and why the underside of a worktop matters more than the surface when thicknesses vary so widely. It sets out the three counter height bands found in UK homes and the seat height each requires, then covers the factors that quietly change effective height, including foam compression, floor coverings, foot glides and footrest position. It closes with a simple stacked box test you can run at your own counter before ordering anything....

Continue Reading
How Much Space for Bar Stools at Island?
August 12, 2026

How Much Space for Bar Stools at Island?

Space planning for island seating rests on three figures, and this guide explains each one and how they interact. Width per stool comes first, with 60cm suiting armless designs and 70cm needed for arms or wide seats, measured centre to centre so the person is accounted for rather than the object. The walkway behind comes next, including how much a backless stool projects compared with one that has a backrest, and why 90cm is the floor rather than the target. Vertical clearance and worktop overhang are covered together, since a shallow overhang undoes a good height. There is also practical advice on where to position stools, why corner seating rarely works, how seating interacts with appliance doors and the working triangle, and a floor marking test to run before ordering....

Continue Reading
How Do You Remove Gas Strut from Bar Stool?
August 12, 2026

How Do You Remove Gas Strut from Bar Stool?

Gas strut and gas cylinder describe the same part: the pressurised chrome column that raises and locks a bar stool seat. Removing one is straightforward once you know it is held by a tapered friction fit rather than a thread. This guide starts with the checks worth doing first, since a wobble may only be loose bolts and a rising seat may only be a misaligned lever. From there we cover the tools, why working on a hard floor matters, and how to release both the swivel plate joint and the tighter base joint using a mallet and a hardwood block. We also set out the genuinely unsafe mistakes to avoid, how to measure and fit a replacement correctly, and when starting again beats repairing....

Continue Reading
What Are Standard Bar Stool Heights?
August 12, 2026

What Are Standard Bar Stool Heights?

Standard bar stool heights sound like a settled matter until you compare two products described the same way and find several centimetres between them. This guide sets out the three counter categories in clear centimetres, explains where low vanity stools fit and why they are easy to buy by mistake, and gives the clearance principle that lets you calculate the right seat height for any worktop. We look at why stated heights vary between manufacturers, from upholstery compression to differing measuring conventions and imported counter standards, and how much margin to allow. There is practical guidance on measuring your own counter to both the underside and the surface, why the overhang matters, and the comfort measurements that height alone does not capture: seat depth, seat width, footring drop and backrest profile. We close with choosing heights across a room that has more than one counter level....

Continue Reading
How Do You Lower a Bar Stool?
August 12, 2026

How Do You Lower a Bar Stool?

Lowering a bar stool depends entirely on its mechanism, and identifying that comes first. A gas lift stool needs weight on the seat while the lever is held, because body weight is what pushes the cylinder down: this is why so many stools seem to rise but never descend. A threaded stool lowers by spinning the seat clockwise, and a fixed stool has no adjustment at all. This guide covers each case, plus what to do when the lever moves but nothing happens, why a sinking cylinder cannot be repaired and how a clamp can hold one at a set height, how to calculate the seat height your counter actually needs, and a reliable way to get a whole set matching....

Continue Reading
How Do You Cut the Legs on a Bar Stool?
August 12, 2026

How Do You Cut the Legs on a Bar Stool?

Shortening bar stool legs is straightforward with the right preparation, and almost every failure comes from marking rather than cutting. This guide covers how to work out exactly how much to remove using your counter height and compressed seat height, and how to check first whether the stool can be cut at all: footrest position, leg taper and splay, joint locations and construction type all set limits, and a gas lift column cannot be shortened. It then walks through marking a square line on round and square legs, taping to prevent chipping, cutting timber with a fine tooth saw and tubular metal with a hacksaw or pipe cutter, and finishing the ends properly. Levelling advice, rust prevention on cut steel and the alternatives worth considering before reaching for a saw are included....

Continue Reading
How Do You Baby Proof Bar Stools?
August 12, 2026

How Do You Baby Proof Bar Stools?

Baby proofing bar stools has less to do with fitting accessories than with rearranging a kitchen so climbing becomes difficult and falling becomes unlikely. The measures that work follow a clear order: remove access by tucking stools fully under the counter, improve stability with non slip pads and tightened fixings, then neutralise moving parts like gas lifts and swivel seats before softening the floor beneath. This guide explains the three distinct risks stools present to small children, which design features to look for if you are buying during the toddler years, and which to avoid entirely. We also cover the age at which a stool becomes appropriate seating, why a highchair or a low table remains the right answer before then, and the household habits that matter more than any single modification in a busy UK family kitchen....

Continue Reading
Why Are Bar Stools So Uncomfortable?
August 12, 2026

Why Are Bar Stools So Uncomfortable?

Discomfort on a bar stool is rarely a padding problem. Once your feet leave the floor your legs stop carrying weight, and everything transfers to the underside of the thighs and the base of the spine, which is why a badly placed footrest ruins an otherwise well made seat. This article works through the real causes in order: dangling feet, a footrest at the wrong height, a knee gap that is too tight or too generous, a seat that is too narrow or has a hard front edge, foam that has quietly compressed, and a backrest that sits below the lumbar region and supports nothing. It also looks at posture and how long people actually sit at an island, then sets out low cost improvements for stools you already own, from replacement foam and a firmer pad to simply reducing the number of seats along a run....

Continue Reading
Are Bar Stools or Counter Stools Taller?
August 12, 2026

Are Bar Stools or Counter Stools Taller?

Bar stools are the taller of the two, with seats at 70cm to 78cm against 60cm to 66cm for counter stools, and this article explains why that 10cm to 15cm gap is not arbitrary. Both categories are built around the same 25cm to 30cm of clearance a seated adult needs beneath a surface, and the gap simply mirrors the two common surface heights found in British homes. We set out what genuinely goes wrong when the categories are swapped, from 15cm of trapped legroom to a 40cm reach that lifts your shoulders while eating, and how to measure your counter underside to identify which band you are in. There is practical comparison of how each type behaves in a compact UK kitchen, why taller stools need wider bases and footrests, and the three situations where an adjustable column spans both. We also compare how each height looks in a room and behaves in daily use....

Continue Reading
How Do You Tighten a Swivel Bar Stool?
August 12, 2026

How Do You Tighten a Swivel Bar Stool?

A swivel bar stool that wobbles or clicks is almost always a maintenance job rather than a fault, and it can usually be resolved in a few minutes. This article walks through diagnosing where the movement actually comes from, then tightening the three places that loosen: the swivel plate bolts under the seat, the centre fixing at the column, and the leg and footrest fixings. We explain why to tighten diagonally rather than in a circle, how to avoid stripping threads in a board seat base, and why worn floor glides cause wobble that no amount of tightening will fix. There is guidance on thread locking compounds, replacing failed threads with inserts, recognising a worn swivel bearing or gas lift, and a simple twice yearly routine....

Continue Reading