Furniture in Fashion Blog
Furniture in Fashion Blog
Furniture in Fashion Blog
Bathroom lighting zones are areas around the bath, shower and basin that set how water resistant a light fitting must be. In UK wiring regulations there are three zones. Zone 0 is inside the bath or shower tray and needs fittings rated at least IPX7 on a safety extra low voltage supply. Zone 1 is the space directly above the bath or shower up to 2.25m from the floor and needs at least IPX4. Zone 2 extends 0.6m beyond Zone 1 and also needs at least IPX4. Anywhere outside these areas has no specific IP requirement, although a splash resistant fitting is still sensible in a steamy room.
Once you know which zone each fitting sits in, choosing safe lights becomes much simpler. Every fitting in our modern bathroom lighting UK range lists its IP rating, so you can match it to the right position. Below, we explain each zone in plain terms and show how they apply to real UK bathrooms, from compact shower rooms to larger family spaces.
Why Bathroom Zones Exist
Water and electricity do not mix, and a bathroom brings them closer together than any other room in the home. The zone system exists to make sure that the closer a fitting is to water, the better protected it is against splashes, jets and immersion.
The zones come from BS 7671, the UK standard for electrical installations, often called the wiring regulations. These regulations apply to new work and alterations, and they are what a qualified electrician will follow when fitting or moving lights in your bathroom. The same principles apply whether you are choosing a single mirror light or planning a full scheme from our modern lighting UK collection.
Understanding IP Ratings First
Before looking at the zones, it helps to understand IP ratings, because each zone is defined by the minimum rating it requires.
IP stands for Ingress Protection. The rating has two digits:
- The first digit shows protection against solid objects such as fingers, tools and dust, on a scale from 0 to 6.
- The second digit shows protection against water, on a scale from 0 to 8.
Where you see an X, as in IPX4, it means the fitting has not been rated for solids, only for water. A few ratings you will see often in bathroom lighting:
- IP20: protected against fingers, no water protection. Suitable outside the zones only.
- IP44: protected against small objects over 1mm and splashing water from any direction.
- IP65: dust tight and protected against low pressure water jets.
- IP67: dust tight and protected against temporary immersion.
A higher rating can always be used in a lower zone, but never the other way round.
Zone 0: Inside the Bath or Shower Tray
Zone 0 is the interior of the bath or shower tray itself, the space that can actually hold water. Fittings here must be rated at least IPX7, which means they can withstand temporary immersion.
They must also run on a safety extra low voltage supply, commonly 12V, with the transformer placed safely outside the zones. In practice, very few homes put lights in Zone 0. Where they do, it is usually small LED lights set into the side of a bath or the floor of a large walk in shower, designed specifically for this purpose.
Zone 1: Directly Above the Bath or Shower
Zone 1 covers the area directly above the bath or shower tray, up to a height of 2.25m from the finished floor. For a walk in shower without a tray, it extends to 1.2m from the water outlet. Fittings here need a minimum of IPX4.
Where a shower can spray water directly at the ceiling, or where jets are used for cleaning, many electricians recommend IP65 for extra protection. Recessed spotlights are the usual choice above a shower, because they sit flush with the ceiling and keep water away from the electrics. Our modern spotlights UK sale include sealed designs suited to this kind of position.
In a room with a low ceiling, where the ceiling above the bath sits below 2.25m, the ceiling itself falls within Zone 1. This is common in older terraced houses and loft conversions, so check your ceiling height before choosing fittings.
Zone 2: The Area Around the Bath or Shower
Zone 2 extends 0.6m horizontally outward from the edge of Zone 1, again up to 2.25m high. It also covers the space above Zone 1 where the ceiling is higher than 2.25m, up to that height. Fittings in Zone 2 need a minimum of IPX4.
This zone often includes the area where a basin and mirror sit in a smaller bathroom. Current regulations do not create a separate zone around the basin, but many electricians treat the area within 0.6m of a basin tap as Zone 2 as good practice, and recommend IP44 fittings there. It is a cautious approach that makes sense where splashes are common.
Illuminated mirrors are a good example. A mirror sitting close to a shower screen or bath will usually fall within Zone 2. Our illuminated bathroom mirrors UK list their ratings so you can check them against the space.
Outside the Zones
Anywhere beyond Zone 2, or above 2.25m in a room with a high ceiling, is outside the zones. Here, there is no specific IP requirement under the regulations. That said, bathrooms are humid and condensation can reach every surface, so IP44 is still a good choice for most fittings.
Decorative pendants and chandeliers are sometimes used in larger bathrooms. These should be placed outside the zones and checked for suitability in a humid environment. Remember too that steam rises, so a fitting above the zones can still be exposed to more moisture than you might expect.
What About Zone 3?
Older guides and some websites still mention Zone 3. This zone was removed from the wiring regulations some years ago, and the space it once covered is now treated as outside the zones. If you see Zone 3 in a product listing, it is worth checking that the rest of the information is up to date.
Applying Zones in Real UK Bathrooms
Compact shower rooms
In a small shower room, much of the space can fall within Zone 1 or Zone 2. This often means every fitting in the room needs at least IP44. Recessed spotlights and a sealed flush ceiling light keep things simple.
Family bathrooms
A typical family bathroom with a bath along one wall and a basin opposite usually has a clear outside zone area in the centre of the room or near the door. This is where you might place a statement ceiling light, keeping IP rated spotlights over the bath.
En suites in loft conversions
Sloping ceilings can drop below 2.25m above a shower or bath, pulling the ceiling into Zone 1. Measure carefully, and choose IP65 spotlights where the ceiling slopes over water.
Wet rooms
Without a tray or screen, water can travel further in a wet room. Zone 1 extends 1.2m from the shower outlet, and it is wise to treat a generous area beyond that with caution.
How to Map the Zones in Your Own Bathroom
You do not need specialist tools to get a rough idea of where each zone falls. A tape measure, a pencil and a simple floor plan are enough.
- Draw the outline of the room and mark the bath, shower tray or shower outlet, basin and door.
- Shade the bath and shower tray as Zone 0.
- Mark the same footprint as Zone 1, then note the ceiling height above it. If the ceiling is lower than 2.25m, it falls within Zone 1.
- Measure 0.6m out from the edge of Zone 1 in every direction and mark that band as Zone 2.
- Note any areas near the basin taps that you would like to treat as Zone 2 for extra caution.
- Everything left over is outside the zones.
This sketch will not replace a professional assessment, but it helps you shortlist suitable fittings and have a more useful conversation with your electrician.
Other Safety Points to Know
Zones are only one part of bathroom electrical safety. A few other points are worth keeping in mind:
- All circuits serving a bathroom should be protected by a 30mA residual current device (RCD).
- Switches are commonly placed outside the room or replaced with a ceiling pull cord.
- Some bathroom electrical work is notifiable under Building Regulations. A registered electrician can certify the work for you.
- Ventilation helps protect fittings and furniture from moisture over time.
Products sold in the UK should also carry the right safety markings. Our article on lighting safety standards and UKCA marking in the UK explains what those labels mean. Moisture affects furniture as well as fittings, and our guide to how UK bathroom cabinets handle humidity covers which materials cope best near the bath and shower.
Planning With Confidence
Bathroom lighting zones can look complicated on paper, but they follow a simple logic: the closer to water, the higher the protection. Sketch your bathroom, mark the bath, shower and basin, measure out the zones and note the IP rating needed for each fitting. Then share that plan with your electrician before work begins.
We list clear IP ratings on our spotlights, ceiling lights, wall lights and mirrors to make that process easier. At Furniture in Fashion, we want your bathroom to look good and stay safe for years, with free delivery to most UK mainland postcodes.
Frequently Asked Questions
What IP rating do I need above a shower?
At least IPX4 in Zone 1, although IP65 is often recommended where the shower can spray water directly at the ceiling.
Can I use a normal ceiling light in a bathroom?
Only outside the zones. Even then, a fitting rated IP44 is a sensible choice because of steam and condensation.
Is the basin a bathroom zone?
Current regulations do not set a separate zone around the basin, but many electricians treat the area within 0.6m of the tap as Zone 2 and use IP44 fittings there.
Does Zone 3 still exist?
No. Zone 3 was removed from the wiring regulations, and that space is now treated as outside the zones.

No Comments
Sorry, the comment form is closed at this time.