Yes. IP65 lights are suitable for bathrooms, and they can be used safely in almost every part of the room, including directly above a bath or shower. An IP65 fitting is completely sealed against dust and protected against jets of water from any direction, which is more protection than the minimum usually required near a bath or shower. The only place where IP65 is not enough is Zone 0, the inside of the bath or shower tray, which calls for a fitting rated for immersion and supplied at extra low voltage.
That answer covers most homes. The rest of this guide explains the detail behind it, so you understand what the rating actually means and can choose fittings with confidence. If you are already looking at options, our modern bathroom lighting UK range lists the IP rating for each fitting.
IP stands for Ingress Protection. The two numbers that follow describe how well a product is sealed against solids and liquids.
So IP65 describes a fitting that dust cannot enter and that can be sprayed with water without harm. Sometimes you will see an X in place of a digit, as in IPX4. That simply means the fitting has not been tested for that category, usually solids, and the rating refers to water only.
UK wiring regulations divide a bathroom into zones according to how likely each area is to get wet. The zones decide which fittings can go where.
The inside of the bath or shower tray. Any light here must be rated for immersion, typically IPX7, and must run on extra low voltage, usually 12 volts. Lights in this zone are uncommon in homes.
The area directly above the bath or shower tray, up to a height of 2.25 metres from the floor. A minimum of IPX4 is generally required, and many electricians prefer IP65 here because shower water can strike the ceiling or wall at force.
The area extending 0.6 metres outward from the edge of the bath or shower, again up to 2.25 metres high. The space above Zone 1, up to the ceiling, is often treated similarly in practical guidance. A minimum of IPX4 is generally required.
Anywhere beyond Zone 2. There is no specific IP requirement here under the zone rules, but steam and condensation still reach these areas, so many electricians recommend a rating of at least IP44 for bathroom fittings throughout the room.
Zone definitions can vary depending on the room layout, such as a walk in shower without a tray, so it is always sensible to have a qualified electrician confirm the zones in your own bathroom.
If IPX4 is the usual minimum in Zones 1 and 2, why do so many people choose IP65? There are several good reasons.
An IPX4 fitting is protected against splashing. A powerful shower, especially one with a handheld head, can direct a jet of water upwards. IP65 is designed for exactly that kind of exposure.
The dust tight seal of an IP65 fitting also keeps out the small insects and fluff that often collect inside bathroom lights. That means the glass stays clearer and the light output stays consistent.
Fully sealed fittings resist moist air entering the body of the light. In a bathroom without strong ventilation, that helps protect the internal components and the finish.
Choosing IP65 throughout gives you freedom to move a light during planning without needing to recheck whether it falls inside or outside a zone. In small UK bathrooms where everything sits close together, that flexibility is valuable.
Our wider modern lighting UK sale collection includes IP65 designs in several styles, which is useful if you want fittings that coordinate with lights elsewhere in the house.
IP65 is not limited to plain functional fittings. You can find it across most of the shapes used in modern bathrooms.
If you want to direct light more precisely, browse our modern spotlights UK range and check each fitting’s rating against its intended zone. For walls, our selection of modern wall lights UK includes sealed options that suit bathrooms.
Older sealed fittings could look bulky and utilitarian. Modern designs are much more refined. Slim gaskets, integrated LEDs and better glass mean IP65 lights now come in brushed brass, matt black, chrome and satin nickel finishes, with frosted, opal and ribbed diffusers. You no longer have to choose between safety and style.
What does change is the way the fitting is maintained. Because the shade is sealed, replacing a bulb, where the fitting uses one, can involve unscrewing a cover and reseating a gasket. Many IP65 lights use integrated LEDs that are designed to last many years, which avoids the issue altogether.
A sealed light is only one part of a bathroom that copes well with moisture. Furniture, cabinets and finishes all need to handle humidity too. Our guide to bathroom cabinet humidity and materials in UK homes explains how different materials behave in steamy rooms, which is useful context if you are planning lighting and storage together.
Ventilation matters too. An extractor fan that clears steam quickly will reduce condensation on light fittings, mirrors and walls. Some extractor fans incorporate lights of their own, and these also carry IP ratings, so check them in the same way.
Bathroom lighting must be installed correctly to be safe. In England and Wales, most electrical work in bathrooms is notifiable under building regulations, which means it should be carried out by a registered electrician who can certify it, or inspected by building control. Similar rules apply elsewhere in the UK. Circuits serving bathrooms are generally protected by a residual current device, which cuts power quickly in the event of a fault.
An IP65 rating only holds if the fitting is installed as the manufacturer intends. A cracked shade, a missing gasket or a cable entry that has not been sealed properly will compromise protection. If a fitting is damaged, replace it rather than repair it yourself.
Sealed lights are easy to look after. Switch off the power, allow the fitting to cool, then wipe the glass and metal with a soft damp cloth. Avoid abrasive cleaners and strong chemicals, which can damage finishes and seals. Even though the fitting can resist water jets, there is no need to spray it directly when cleaning.
Check the seals occasionally, particularly in older fittings. If you notice moisture inside the shade, the gasket may have failed, and an electrician should inspect the light.
Open showers without a tray change how zones are measured. In a wet room, water can travel across a much wider area of floor and wall, so Zone 1 and Zone 2 may extend further than they would around a conventional enclosure. This is one of the situations where IP65 throughout the room makes particular sense. It removes the guesswork about exactly where spray will land and gives every fitting the same level of protection, from the ceiling above the shower to the wall lights near the basin.
In most UK bathrooms, a sensible plan looks like this: IP65 downlights above the bath or shower, IP44 or IP65 wall lights at the mirror depending on how close they sit to water, and a sealed ceiling fitting for general light. Combine that with good ventilation and moisture resistant furniture, and the room will stay safe and comfortable for years.
At Furniture in Fashion, we bring together bathroom lighting and furniture so you can plan a coordinated room, with free delivery to most UK mainland postcodes.
Yes. IP65 exceeds the usual minimum of IPX4 for Zone 1, the area directly above a bath or shower, making it a popular choice for shower downlights.
No. Zone 0 requires a fitting rated for immersion, typically IPX7, running at extra low voltage. IP65 is not designed for that.
IP44 meets the minimum for Zones 1 and 2 in many situations, but IP65 gives better protection against direct water jets and dust, so it is often preferred above showers.
Many are, as the rating covers rain and dust. However, always check that the manufacturer specifies the fitting for outdoor use before installing it outside.
Brushed brass has become a favourite finish in UK bathrooms because it is warmer than…
Monochrome bathrooms depend on contrast, and that makes them unforgiving of poor lighting. White surfaces…
A charcoal grey contemporary bathroom can look sophisticated and calm, but it needs well planned…
Modern townhouses are built upward rather than outward, which means their bathrooms are often narrow,…
Downstairs WCs are often small, narrow and short on daylight, yet guests see them more…
A classic English contemporary bathroom combines traditional forms such as panelling, washstands and roll top…
This website uses cookies.