Yes, mirror sliding wardrobe doors can be replaced, and in most cases you can do it without touching the wardrobe carcass. Sliding doors are not fixed to the unit in the way hinged doors are. They hang from rollers running in a top track and are guided by a bottom track, so a damaged or dated panel usually lifts out and a new one drops in.<\/p>\n
The important question is not whether replacement is possible but whether your existing tracks will accept a new door. That depends on the track profile, the panel thickness and the roller fixings, and it is worth checking before ordering anything.<\/p>\n
Most systems fall into one of two types. Top hung doors carry their weight on rollers fixed to the top of the panel, running inside a track screwed to the underside of the wardrobe top or the ceiling. The bottom track simply steers the door and takes no load.<\/p>\n
Bottom rolling doors sit on wheels at the base of the panel, running along a floor level track, with the top channel acting only as a guide. These are common in older units and in freestanding wardrobes.<\/p>\n
Identifying which you have takes a moment. Open the door fully and look at the top and bottom edges. If the wheels are at the top, it is top hung. If the panel visibly rests on rollers below, it is bottom rolling. That distinction determines what replacement panels will fit.<\/p>\n
Four measurements matter. First, the panel height and width, taken from the existing door rather than the opening. Second, the panel thickness, usually 10mm, 16mm or 18mm depending on whether the mirror is bonded to a board. Third, the track profile, including the internal channel width. Fourth, the roller centres and fixing type.<\/p>\n
Photograph the rollers and the track ends before ordering. Many replacement panels are sold as a system, and mixing a panel from one system with tracks from another rarely works cleanly.<\/p>\n
If the wardrobe is a branded fitted system, the original supplier is usually the quickest route to a matching panel. For freestanding units, a like for like replacement door from the manufacturer is often available.<\/p>\n
Mirror panels are heavy and awkward. A full height door can weigh 20kg to 30kg, and the risk is not just breakage but the panel flexing and cracking while you carry it. Have a second person present.<\/p>\n
Lay a blanket or several layers of cardboard on the floor where the panel will go. Wear cut resistant gloves and safety glasses. Clear the room of anything you might trip over.<\/p>\n
For a top hung door, slide it to the centre, lift slightly to disengage the bottom guide, then tilt the base towards you and lower the rollers out of the top track. Some systems have a release catch or an anti jump screw that must be loosened first.<\/p>\n
For a bottom rolling door, tilt the top out of the guide channel and lift the panel off its floor track. Adjustment screws at the base sometimes need lowering to gain enough clearance.<\/p>\n
Carry the panel vertically, never flat. A large mirror carried horizontally flexes in the middle and that is where it will break.<\/p>\n
Before the new door goes in, clean both tracks thoroughly. Grit, carpet fibres and old lubricant in a bottom track cause most of the sticking and juddering people blame on the doors themselves. A vacuum nozzle followed by a damp cloth is usually enough.<\/p>\n
Check the tracks for level and for straightness. A bottom track that has sagged or lifted at one end will never let a door run smoothly. Re fix it before fitting the panel.<\/p>\n
Install in the reverse order of removal: top rollers into the track first for top hung doors, then locate the bottom guide. Fit the rear panel before the front one.<\/p>\n
Then adjust. Almost all sliding doors have height adjustment screws at the roller or the base wheel. Turn them a little at a time to bring the panel edge parallel with the wardrobe side, checking the vertical gap along its full height. The doors should meet flush at the overlap with an even shadow line.<\/p>\n
Sometimes the doors are fine and the running gear has worn out. Rollers flatten, bearings seize and aluminium tracks distort under years of use. Replacement roller sets are inexpensive and often solve a door that jumps or drags.<\/p>\n
If the track itself is bent, or the wardrobe carcass has moved so the opening is no longer square, a new panel will not fix the symptom. At that point replacing the whole unit is the more honest solution. Our modern sliding wardrobes UK sale<\/a> range arrives with matched tracks, rollers and panels, which removes the compatibility guesswork entirely.<\/p>\n Not everyone wants to keep the mirror. Plain, wood effect and high gloss panels all work on the same tracks provided the thickness and fixings match, and a non mirrored front can make a bedroom feel less busy.<\/p>\n If you replace a mirrored door with a solid one, you will probably want the reflection back somewhere. A wall mounted or freestanding piece from our modern bedroom mirrors UK sale<\/a> selection covers that, and the cheval mirrors UK sale<\/a> designs give a full length view that can be angled properly for dressing.<\/p>\nAlternatives to a Mirrored Replacement<\/h3>\n