You cover a dining chair with fabric by removing the seat pad, laying your chosen fabric face down, centring the pad on top of it, then pulling the fabric taut and stapling it to the underside of the base, working from the middle of each side outwards and folding the corners last. On chairs with a fixed seat, the same principle applies, but the fabric is stapled to the frame rail underneath and finished with braid or a dust cover. Most standard dining chairs take under an hour each once you have a rhythm going.
That is the whole job in a paragraph, but the difference between a chair that looks freshly made and one that looks homemade sits in the details: fabric weight, how you handle the corners, and how evenly you tension the cover. Below is a full walkthrough written for real UK homes, where the dining chair is usually the hardest working seat in the house.
Dining chairs tend to fail in one place only. The frame stays sound for decades while the seat fabric thins, marks or fades. Recovering lets you keep a frame you like and reset the look of the room for the cost of a couple of metres of cloth. It is also a practical way to bring older chairs into line with a newer table, or to move a set from a formal scheme into something softer.
There is a point where recovering stops being sensible. If the joints wobble, the webbing has collapsed, or the frame has been repaired more than once, you are decorating a problem rather than solving it. In those cases it is worth looking at replacement fabric dining chairs UK sale ranges instead, then keeping your recovering skills for pieces that genuinely deserve them.
The tool list is short and most of it is reusable. A staple gun, ideally with 8mm or 10mm staples, is the one item worth buying properly. Manual guns work on softwood frames, but if the beech frames on your chairs are hard, an electric gun saves your hand.
You will also want fabric scissors kept only for fabric, a tack lifter or flathead screwdriver to remove old staples, pliers to pull stubborn ones, a screwdriver for the seat fixings, a tape measure, tailor’s chalk and a small hammer. Add a bag of upholstery foam or wadding if the existing padding has flattened, and a roll of calico if you want a proper underlayer.
Dining seats take a lot of abrasion, so the fabric specification matters more than the pattern. Look for upholstery weight cloth rather than dress or curtain fabric. Most upholstery fabrics carry a rub test figure, and anything rated for general domestic upholstery will handle a dining room. Lighter cloths can be backed to improve their performance, but a thin fabric will always wear at the front edge first.
Weave tightness helps too. A close weave resists snagging from buttons, belts and pet claws, while loose bouclé looks lovely and pulls easily. Velvets sit somewhere in between: they wear well, mark less than people expect, and brush clean. If you like that finish but would rather buy it ready made, our velvet dining chairs UK selection shows how the fabric behaves across different frame styles.
Colour choice is worth a moment of honesty. Pale seats in a room used daily by a family will need cleaning often. Mid tones, textured weaves and small patterns hide the ordinary marks of family life far better than flat pale cloth.
Measure the seat pad at its widest and deepest point, then add the depth of the pad twice plus 5cm on every side for pulling and stapling. A typical dining seat needs a piece roughly 55cm by 55cm. Standard upholstery fabric comes 140cm wide, so you can usually cut two seats across the width, meaning four chairs need about 1.2 metres. Buy a little more than the sum suggests. Off cuts are useful for testing staples and for repairs later.
Patterned fabric changes the maths. If the design has a repeat you want centred on each seat, you need enough length to place the motif in the same position every time, and that can add a third to the total.
Drop in seats are the easiest place to start because the pad lifts straight out of the frame. Turn the chair over, undo any screws holding the pad, and push the seat up from underneath.
Strip the old cover if it is bulky or damaged. If it is thin and clean, you can often cover straight over the top, which saves time and keeps the pad firm in the frame. Remove old staples with a tack lifter so the new ones seat properly.
Check the padding. If the foam has compressed unevenly, replace it with a new piece cut to the pad shape, then add a layer of polyester wadding over the top to soften the edges. Wadding is what stops a recovered seat looking hard and boxy.
Lay the fabric face down on a clean floor or table, place the pad centrally on top, padding side down, and check any pattern is straight against the pad edges. Fold one long side up and put a single staple in the centre. Do the same on the opposite side, pulling firmly so the cloth is taut but not distorted. Repeat on the two remaining sides. You now have four anchor points holding the fabric square.
Work outwards from those anchors, adding staples every 3cm to 4cm and stopping about 6cm short of each corner. Keep checking the top face as you go. Tension should be even, with no ripples pointing towards the staples.
Corners are what separate a tidy job from a lumpy one. On a square pad, pull the fabric straight up at the corner point, staple it, then fold the two side flaps in neatly like wrapping a parcel and staple each fold down flat. Trim away bulk inside the fold before stapling if the fabric is thick.
On a rounded corner, gather the excess into several small even pleats rather than one large fold. Aim for pleats that all face the same direction so they read as deliberate. Take your time here: the extra two minutes shows in the finished chair.
Trim the surplus fabric back to about 2cm from the staple line, then staple a piece of black bottom cloth over the underside if you want a professional finish. Drop the pad back into the frame and refit the screws.
When the seat is part of the frame, the process is the same but you work in place. Remove any existing braid, gimp or studs first, then strip the old cover back to the padding. Take a photograph before you start so you have a reference for how the original was folded around the legs and back posts.
Fabric on a fixed seat has to be cut into around the uprights. Make a straight cut towards each post, stopping just short of it, then a small Y shaped split so the two flaps can tuck neatly either side. Cut less than you think you need at first, since you can always extend the cut, and staple the tucked edges out of sight underneath the rail.
Finish the visible edge with braid glued in place, or with decorative studs spaced evenly along the rail. A simple double piped braid in a matching tone is the most forgiving option for a first attempt.
Recovered chairs look best when the fabric relates to something else in the room rather than floating on its own. Pick up a tone from your curtains, rug or artwork. If your table is timber, a natural weave keeps the pairing calm, while a deeper solid colour gives the set more presence in an open plan space.
It is also worth thinking about the room as a whole before you commit to a colour. Seeing complete sets together, as with our modern dining table and chairs sets UK, is a quick way to test whether you want your seats to blend into the scheme or stand apart from it. At Furniture in Fashion we see plenty of customers pair a timber table with a single accent seat tone, which is an easy effect to copy at home with fabric alone.
Vacuum the seats with a brush attachment every few weeks so grit does not sit in the weave and cut the fibres. Deal with spills immediately by blotting rather than rubbing, and always test any cleaning product on the underside first. Rotate your chairs occasionally so the two seats nearest the kitchen door do not wear ahead of the rest.
If the room gets strong afternoon sun, expect some fading over time. Closing blinds during the brightest hours helps, and it is another reason to keep a spare piece of fabric from the original roll.
Recovering is satisfying, but it does not fix comfort. If the seat height is wrong for your table, if the back offers no support, or if the frames were never comfortable to sit in for a long meal, new fabric will not change your evenings. Browsing current modern dining chairs UK options alongside the cost of materials usually makes the decision clear within a few minutes.
Yes, provided the existing cover is smooth, dry and not badly worn. Covering over the top adds bulk, so check the pad still drops into the frame before you staple everything down.
A tightly woven upholstery fabric or a good quality velvet in a mid tone. Both resist everyday marking and brush clean easily, which matters more than any single fibre type.
Not for drop in seats, which are stapled rather than sewn. You only need to sew if you are making piping, a skirt or a loose slip cover.
Allow about an hour for your first chair and roughly half that for the rest. Stripping old staples takes longer than fitting the new fabric.
No. The cover is decorative and the strength comes from the frame and webbing. If the chair already feels loose, tighten the joints before you start.
Painting faux leather dining chairs is entirely possible, but the outcome depends far more on…
Hard dining chairs can be made genuinely comfortable, and there are three practical routes depending…
Chair spacing has a disproportionate effect on how comfortable a dining table feels, and the…
Comfortable dining comes down to two measurements: around sixty centimetres of table edge per person…
Reupholstering a dining chair cushion is one of the most approachable furniture jobs there is,…
Reupholstering a dining chair in the UK generally costs between sixty and two hundred pounds…
This website uses cookies.