You build a round dining table by gluing timber boards into a panel wider than your finished diameter, cutting a true circle from that panel using a router on a trammel arm, shaping and sanding the edge, then fixing the top to a pedestal or four leg base using fittings that allow the wood to move. For a four seater, aim for a diameter of 100cm to 110cm. For six people, 120cm to 140cm. The circle cutting stage is the part that intimidates people, and it is genuinely the easiest step once the jig is set up.
A round table is a good first serious furniture project. There are no mitred corners to fight, the geometry is forgiving and the finished piece suits British rooms well, since a circle takes up less visual space than a rectangle of equivalent seating and has no corners to catch hips in a narrow room.
Lay your boards out and arrange them for grain and colour before you commit. Alternate the growth rings if you can see them on the end grain, which helps balance any cupping over time. Mark a triangle across the boards so you can reassemble the order after applying glue.
Apply an even bead of glue to one mating edge of each joint, spread it with a brush or finger, and clamp with alternating clamps above and below the panel to keep it flat. Do not over tighten: you want a thin, even glue line, not a starved joint. Scrape off squeeze out once it reaches a rubbery stage, roughly half an hour in, which saves considerable sanding later.
Leave the panel clamped overnight. Then flatten it with a hand plane, a belt sander or a router sled if the boards are not perfectly aligned.
Find the centre of your panel by measuring diagonals or using a long straight edge. Drill a shallow pivot hole, ideally not all the way through, and screw one end of your trammel arm to it. Mount the router at the other end, with the distance from pivot to the outer edge of the cutter equal to your finished radius.
Rough cut close to the line with a jigsaw first, leaving around 5mm. This reduces the work the router has to do. Then take the circle in several shallow passes, going no deeper than 4mm at a time, rotating the router steadily around the pivot. Rushing this produces burn marks and chipping on the grain that runs across the cut.
A jigsaw and patience will get you there. Mark the circle with a pencil on a string, cut just outside the line, then true the edge with a sanding block wrapped around a curved former. It takes longer and the result depends on your care, but it is entirely possible.
A square edge on a round table looks unfinished and feels sharp when you lean against it. A small roundover, a chamfer or a bullnose profile all work. Run the router around the edge with a bearing guided bit, top and bottom, keeping the movement continuous to avoid burn marks.
Sand through the grits: 80, 120, 180 and finally 240. Sand the edge by hand rather than with a machine, since it is easy to flatten a curve without noticing. Wipe the surface with a damp cloth between the last two grits to raise the grain, let it dry, then sand lightly again. This step is what makes the finished surface feel smooth rather than merely look it.
Round tables are usually best on a pedestal, because a central column gives every diner unobstructed leg room and lets people sit anywhere around the edge. A pedestal needs a foot spread of roughly 60 percent of the table diameter to resist tipping when someone leans on the edge.
The alternative is four legs joined by an apron. This is simpler to build with basic tools and very stable, though it restricts seating positions slightly. If you are building for a small room, the pedestal is worth the extra effort. Looking at how manufactured designs solve this problem is genuinely useful before you start, and our wooden dining tables UK sale range shows several pedestal and four leg approaches in detail.
This is where homemade tables most often fail. Solid timber expands and contracts across its width with humidity changes, and a British home swings considerably between damp autumn and dry central heating in January. A top screwed rigidly to a frame at every point will crack.
Use figure of eight fasteners, Z clips in a routed slot, or elongated screw holes that allow lateral movement. Fix firmly at the centre and let the outer fixings slide. The top will move a few millimetres seasonally and nothing will split.
For a dining surface, hardwax oil is the most practical choice for a home workshop. It penetrates rather than sitting on top, it is repairable in patches, and spot damage can be sanded and re oiled without stripping the whole table. Apply thin coats with a cloth, wipe off excess after ten minutes, and allow a full day between coats.
Polyurethane gives a harder, more water resistant film and suits households with young children, but repairs mean refinishing an entire surface. Whichever you choose, finish the underside too. An unfinished underside absorbs moisture at a different rate to the top and encourages cupping.
Allow 60cm of circumference per diner. A 120cm round table has a circumference of roughly 377cm, giving six comfortable places. Then allow 90cm of clearance around the table for chairs to pull out, or 100cm if people need to walk behind seated diners.
In many UK dining rooms, that clearance is the limiting factor rather than the table itself. If your room is tight, a smaller diameter with lighter chairs will feel better than a large table you have to edge around. Slim profile seating helps considerably, and our modern fabric dining chairs UK include several designs with a compact footprint.
If the build turns out to be more than you want to take on, there is no shortage of ready made round designs. You can see the full dining collection at Furniture in Fashion, alongside dining benches UK sale if you want flexible seating around a circular top.
Species affects cost, weight, workability and how the table ages. Oak is the usual choice for good reason: it is hard, widely available, machines cleanly and darkens attractively over years. Ash is lighter in colour with a bold grain and is slightly easier to work. Beech is dense, even textured and takes a finish beautifully, though it moves more with humidity than oak does. Softwoods such as pine are inexpensive and forgiving for a first attempt, but they dent under normal dining use and will show every mark within months.
Buy kiln dried timber rather than air dried where possible, and let the boards sit in the room where the table will live for at least a week before you glue up. Timber brought straight from a cold workshop into a heated house will move, and it is far better for that movement to happen before the panel is assembled than after.
An oiled top wants a light refresh once or twice a year, or whenever water stops beading on the surface. Clean with a barely damp cloth rather than a soaked one, and avoid household sprays containing silicone, which interfere with future oiling. Use trivets under hot dishes: heat marks in an oil finish are repairable but tedious.
Small dents in solid timber can often be raised by placing a damp cloth over the mark and applying a warm iron briefly, which swells the compressed fibres. Sand lightly and re oil the area afterwards. That repairability is one of the real rewards of building the table yourself, since you know exactly what is on the surface and how to renew it.
Between 25mm and 40mm for solid timber. Thinner tops can sag over an unsupported span, and thicker tops become heavy and difficult to fix without visible movement problems.
Yes, and birch ply is stable and cuts cleanly. The exposed edge is the issue, since the layers show. Either embrace it as a feature or apply a solid timber lipping around the circumference before rounding the profile.
Check the foot spread first, then make sure the column meets the top plate squarely. Most wobble comes from an uneven floor rather than the table, so adjustable feet or thin packers under the base are often the real fix.
Often yes. Without corners, a round table allows easier movement past it and seats people more flexibly. The trade off is that a round table cannot be pushed against a wall as efficiently as a rectangular one.
Allow a weekend for the glue up and circle cutting, then several days of finishing with drying time between coats. Working evenings, two weeks is a realistic total for a first attempt.
Reupholstering a dining room chair with leather gives you a hard wearing, wipe clean seat…
The space between a kitchen island and a dining table should be at least 100cm,…
Indoor dining chairs can go outside for an afternoon in dry weather, but they will…
Covering a dining chair seat can mean three quite different jobs, and choosing the right…
A standard dining table is 74cm to 76cm high, but the number that actually determines…
A custom dining table in the UK generally costs between £900 and £4,000, with the…
This website uses cookies.